Connection
Neighbors
Configure
Ethernet
Switch ports status
Switch ports configuration
Cellular Status

Your client connection

Client IP
Client MAC
VLAN
Port
AP radio
Band
Channel
Mode
Max bitrate
Signal

Speed test

Run a browser-based speed test to check your connection to this .

Run speed test

details

Name
Network name
Hardware address
Product model
Signal Strength
Reference Signal Received Power (RSRP)
Reference Signal Received Quality (RSRQ)
Received Signal Code Power (RSCP)
Energy per chip over Noise Spectral Density (EC/N0)
Band
Type
Carrier
APN
Status
Connection
Error Message
IP Type
Platform
Open Source Disclosure	Download



Cellular Uplink	This is connected to a cellular network. Cellular IP address:
Ethernet	This is directly connected to a local network. Primary IP address: Primary IPv6 address: Primary IP address: Primary IPv6 address: This is acting as a repeater and has not detected a uplink connection on an Ethernet port. This is trying to join a network or find a working Ethernet connection. Primary IP address: Primary IPv6 address: This has detected an IP conflict on its uplink connection with another machine.
Internet	This is connected to the Internet. This is not connected to the Internet. This does not have a working DNS server.
	This is not connected to the . Make sure you can send outgoing traffic to UDP port 7351 through your firewall. Make sure you can send outgoing traffic to TCP port 7734 through your firewall. This is successfully connected to the .
Firmware

Cellular Status

VLAN utilization

	VLAN list	VLAN count
Port primary or allowed VLANs
Access port voice VLANs
Access policy guest VLANs
Management VLAN
All VLANs in use

Cellular status

Status
IP
Type
Provider
Model
Access Point Name (APN)
Signal strength
Reference Signal Received Power (RSRP)
Reference Signal Received Quality (RSRQ)
Band

Stacking Status

Hardware Addresss	Product Model	Current

Neighbors

SSID	BSSID	Channel	Signal (dB)	Mode	Encryption

Uplink configuration

Configure the uplink Internet connection on this .
Internet 1
- Role
- Active Port
- VLAN tagging
- VLAN ID
- Connection type
- IP assignment
- Address
- Netmask
- Gateway
- DNS server 1
- DNS server 2
- Authentication
- Username
- Password
- IPv4 assignment
- IPv4 address
- IPv6 assignment
- IPv6 link-local address
Internet 2
- Role
- Active Port
- VLAN tagging
- VLAN ID
- Connection Type
- IP assignment
- Address
- Netmask
- Gateway
- DNS server 1
- DNS server 2
- Authentication
- Username
- Password
- IPv4 assignment
- IPv4 address
- IPv6 assignment
- IPv6 link-local address
Safe Mode

In Safe Mode Port 1 Is Configured as a WAN Port. This allows the Port 1 to be plugged into a switch,router and other uplink to access Meraki Cloud even when the cellular network is inaccessible.
Internet 1
- Enable Safe Mode
SIM PIN
- PIN
- Number of PIN attempts remaining
Cellular Information

SIM specific information.
- IMEI
- ICCID
- IMSI
Access Point Name Configuration

Set Cellular Override in order to set APN and other cellular settings.
- Cellular Override
- APN
- Username
- Password
- Cellular Authorization
- Cellular IP Type
- PUK
Uplink configuration

Configure the uplink Internet connection on this .
IP configuration
- IP assignment
- VLAN
- Address
- Netmask
- Gateway
- DNS server 1
- DNS server 2
Site survey

In site survey mode, the AP will always broadcast the open SSID site_survey-<MAC address> and will not check for connectivity with the . This mode should only be used to perform a site survey, not for serving wireless clients.
- Survey mode?
Web proxy

HTTP will be used for the device to communicate with the if UDP communication is blocked
- Use a proxy?
- Hostname or IP
- Port
- Authentication
- Username
- Password
Save
DM Logging

With DM (Diagnostic Monitor) Logging tool, you can capture packet exchanges between the modem and cellular network, and also between the modem and the host platform, which then can be used to debug cellular connectivity or performance issues.

Download support data

Download diagnostic information about this device for Support to examine. This can take several minutes.

Do this only if requested by Cisco Meraki Support.
Ethernet configuration

Use this page to configure physical link settings on the Ethernet ports.

Save

Incorrect password

You've entered incorrect login credentials. The default login is the serial number (e.g. Qxxx-xxxx-xxxx), with no password. The serial number is on the bottom or back of the device.

Try again

Your client connection

Speed test

details

Cellular Status

VLAN utilization

Cellular status

Stacking Status

Meraki peers

Neighbors

Uplink configuration

Internet 1

Internet 2

Safe Mode

Internet 1

SIM PIN

Cellular Information

Access Point Name Configuration

Uplink configuration

IP configuration

Site survey

Web proxy

DM Logging

Download support data

Ethernet configuration

Switch ports status

Switch ports configuration

Incorrect password

You've entered incorrect login credentials. The default login is the serial number (e.g. Qxxx-xxxx-xxxx), with no password. The serial number is on the bottom or back of the device.